XTND2K150
HDANYWHERE HDMI Extender 2K, 5-150 Metres, 2-way IR, RS232, PoE, HDMI loop out
XTND2K150
HDANYWHERE, HDMI Extenders, HDMI Extenders
 (click to expand) |
XTND 2K (150m) is a 2K or 1080p-capable HDMI extender that uses full HDBT technology to extend a 1080p HDMI source device up to 150m over a single Cat 6 cable. It supports two-way IR, allowing you to control the set top box, access all its content like movies, shows, and guides, as normal at your TV... even if the set top box is located out of site.
The transmitter of the XTND 2K (150m) extender has a HDMI output port that allows you to watch your source device on a second display nearby by using a suitable HDMI lead if you wish. If you want to enjoy surround sound audio as opposed to audio simply from your TV speakers, XTND 2K 150 supports this. XTND 2K 150 supports all audio formats from 2.0 channel stereo audio, 5.1 and 7.1 compressed audio formats as well as surround sound uncompressed (Dolby True HD, DTS Master Audio) and object-based formats inc. DTS:X and Dolby Atmos.
Only one 'end' requires power thanks to PoE technology.
(Product Code: XTND2K150 SKU: 2.50.767)
How to extend the range of your 1080p device and watch it on two TVs.
One TV is situated nearby to your HDMI source device / set top box and is connected to the XTND 2K transmitter using a HDMI cable. Your second TV can be located up to 150m away from the XTND 2K transmitter, and is connected to the XTND 2K receiver, also using a HDMI cable. You connect the transmitter and the receiver together using a single Cat 5e /6 cable that cannot be longer than the maximum specified distance. If you need professional installation please contact us for your local installer.
| XTND2K150 Data Sheet  |
XTND2K150 Manual |
XTND2K150 Quick Start guide |
XTND Comparison Chart |
Control
- IR 2-Way (from screen to source and source to screen)
- Sky TV tested (including new smaller KAON set top box)
- Receiver and flasher dimensions as below
NOTE: Make sure the IR Emitter is positioned correctly in front of the IR window on your source device. IR windows may vary in position depending on source/model.
Advanced Control
- RS232 Not applicable
- Third Party Not applicable
- App Control Not applicable (details below for models that apply)
ControlImprove your multiroom HD smart home experience with the HDanywhere Control app for phone or tablet. Watch TV your way Optimised for all devices |
HDMI Extender Wiring Guidance
HDanywhere video distribution systems require a single network cable to be run from each HDTV location, back to a central point.
This article is designed to give you a good overview of the standard of wiring needed for HDMI distribution systems.
What is the best type of cable to use?
Currently you can use Cat5e, Cat6, Cat6e, Cat6a, Cat7 or Cat7a with HDanywhere HDMI Distribution products.
The baseline cable standard for HDanywhere systems is Cat5e. Slightly greater distances can be achieved by using Cat6, or slightly better still with the Cat7, which have thicker copper cores for easier signal transfer.
DO NOT USE COPPER CLAD ALUMINIUM (CCA) Cat 5/6/7 CABLE FOR HDMI Distribution.
Whichever network cable type you choose, ensure that the main wiring architecture is ‘solid core’, not stranded ‘patch’ cabling. Patch cabling can be used for the last few metres of a run (say from a wallplate) but should be avoided over the longer runs as signal transfer over stranded cores is heavily reduced.
The use of pre-made leads is not recommended unless you can be absolutely sure of their construction credentials (i.e. solid core 568B)
-
Shielded cables
Unlike other systems, shielded FTP cable is not a stipulation. If however you preferred this type of cable please ensure compatible shielded accessories are used. Failure to terminate cable screen at all points can induce interference rather than eliminating it.
-
Best Practice
Best practice advice is to always use a straight piece of cable terminated directly at the matrix and the receiver ends.
-
HDMI over CATx with patch panels & wall plates
The use of wallplates and patch panels always has the potential to cause increased resistance on the cable, introducing ‘pinch points’ for signal transmission and could reduce advertised transmission lengths.
TIP – instead of using RJ45 wallplates, use brush plates instead to maintain the neat finish. A search for “brush plates” will yield many results.
-
Connection termination
Terminate the cabling using RJ45 connectors to the 568B wiring standard (shown below).
-
General Troubleshooting Advice
Check that the Cat cable is not bent, knotted, kinked or distorted in any way that would prevent these high frequency signals from traveling throughout the intended length.
Also, ensure that the cables as far away from potential sources of EMI (Electro-Magnetic Interference) such as electrical cables, transformers, light fixtures, etc.) as possible. Cables should maintain a 300mm separation from power cables.
Try re-terminating the RJ45 connectors again, making absolutely sure that every termination is perfect. Ensure that the RJ45 connectors are fully inserted and click locked into place firmly and securely to ensure perfect connector connection
-
Suggested Installation Do’s and Don’ts
DO maintain the twists of the pairs as close as possible to the point of termination, or no more than 13mm untwisted.
DO make only gradual bends in the cable where necessary to maintain the minimum bend radius of 4 times the cable diameter or approximately 30mm radius.
DO use low-to-moderate force when pulling cable. The standard calls for a maximum of 34 N-m (newton-metres of force).
DO use cable pulling lubricant for cable runs that may otherwise require great force to install. (You will be amazed at what a difference the cable lubricant will make)
DO keep Category cables as far away from potential sources of EMI (Electro-Magnetic Interference) such as electrical cables, transformers, light fixtures, etc.) as possible. Cables should maintain a 300mm separation from power cables.
DON’T allow the cable to be sharply bent, twisted, or kinked at any time. This can cause permanent damage to the geometry of the cable and cause transmission failures.
DON’T over-tighten cable ties or use plastic ties.
DON’T EVER splice or bridge Category cable at any point.
DON’T use excessive force when pulling cable.
DON’T use oil or any other lubricant not specifically designed for Category network cable pulling as they can infiltrate the cable jacket, causing damage to the insulation.
DON’T tie cables to electrical conduits, or lay cables on electrical fixtures
DON’T install cables taut. A good installation should have the cables loose, but never sagging.
DON’T use staples on Category cable that crimp the cable tightly. The common T-18 and T-25 cable staples are not recommended for Category cable. However, the T-59 insulated staple gun is ideal for fastening both Category and fibre optic cabling, as it does not put any excess pressure on the cable.
DON’T use patch cords (cables) or punch down blocks.
| XTND2K150 Data Sheet |
XTND2K150 Manual |
XTND2K150 Quick Start guide |
XTND Comparison Chart |
