Home Brands HDANYWHERE

MHUB411U40

Learn More

HDANYWHERE HDMI Matrix, 4x1+1 Ultra HD to 40M or Full HD to 70M

Enquire Find a Dealer

MHUB4K411U40

HDANYWHERE, HDMI Matrix, AV Solutions for 3-4 Rooms, AV Matrix Switchers

Cloud-monitorable 4x1+1 HDMI/HDBT+HDMI matrix system with a 40m UHD 4K or 70m 1080p transmission range.
An integrated IP>IR control processor enables property-wide control of all the connected sources and displays via the free uControl App* or Alexa voice commands.

Multichannel audio or stereo extraction can be selected to occur matched to any of the display zone outputs A or B.
Remote cloud monitoring is also possible, designed to reduce the necessity for callouts and site visits.

uControl Remote Ready!
uControl your smart home tech with one remote. Navigate endless entertainment and scene-setting options, with a unifying remote for all media, music and mood control. Check it out here!

(Product Code: MHUB411U40    SKU: 2.50.852)

MHUB862U40 logos

MHUB4K431U Control


[*] Note: uControl app available for Apple iOS (Android is no longer supported). 

 

Features

HDMI® 2.0 features supported up to 18Gbps
Display receiver powered via PoH
IR over HDMI injector dongle included
Web GUI for easy config and setup (MHUB-OS)
Remote system monitoring (HDA Cloud)
Advanced EDID management
Supports source content up to and inc. Ultra HD 4K 60 4:4:4 with High Dynamic Range (HDR) formats inc. Dolby Vision®
Supports all current audio formats up to and including Dolby Atmos® and DTS:X®
Multichannel audio or stereo extraction via optical, or via 3.5mm stereo jack
Sold as a complete install package, with Receiver, IR cables included.

Specifications

Form factor Compact unit. Mountable with optional mounting wings
Inputs x outputs 4 HDMI x 1 RJ45 HDBaseT + 1 HDMI + 1 mirrored HDMI
Video bandwidth HDMI backplane 594MHz clock / 18Gbps data
HDBT 340MHz clock / 10.2Gbps data
ESD protection ± 8kV (air-gap discharge) ± 4kV (contact discharge)
Hub control Web GUI, IR, TCP/IP, RS232, App, Alexa
App control Full control over sources, matrix hub & display functions.
Device weight Chassis: 1250g
Receiver: 125g 
Package weight 2000g
Dimensions (W/D/H) Hub 220 / 200 / 45mm (without feet)
RX 140 / 65 / 17mm
Operating temperature 32°F to 104°F (0°C to 40°C)
Storage temperature -4°F to 140°F (-20°C to 60°C)
Relative humidity 20~90 % RH (non-condensing)
Power consumption 30W (max) 0.5W (standby)
Guarantee 2/3-year guarantee (Cloud registration required)
MHUB411U40
Data Sheet

pdf-icon-843-498
MHUB411U40
Manual

pdf-icon-843-498
MHUB411U40
Wiring Diagram

pdf-icon-843-498
MHUB  
Control Overview

pdf-icon-843-498


 

HDBaseT Wiring Guidance

HDanywhere video distribution systems require a single network cable to be run from each HDTV location, back to a central point. Some single wire systems use HDBaseT technology to transmit over 1 x Cat5e/6/7 cable up to a 100 Metre distance.

This article is designed to give you a good overview of the standard of wiring needed for a HDBaseT system. 

What is HDBaseT?

HDBaseT is a transmission technology widely used for whole-home and commercial distribution of uncompressed HD multimedia content. The cornerstone of HDBaseT technology is 5Play™, a feature set made up of five key things that are sent over a single Cat cable:

  • Uncompressed high-definition (HD/1080p) and 3D video, plus 4K resolutions
  • Lossless digital audio formats 7.1 and beyond
  • High-speed Ethernet 100BaseT scaling up to Gigabit
  • 100w power over HDBaseT (PoH) up to 100m
  • Various backward + forward control signals (IR, USB, RS232)
What is the best type of cable to use?

Currently you can use Cat5e, Cat6, Cat6e, Cat6a, Cat7 or Cat7a with HDanywhere HDBaseT-based products. The baseline cable standard for HDanywhere systems is Cat5e. Slightly greater distances can be achieved by using Cat6, or slightly better still with the Cat7, which have thicker copper cores for easier signal transfer.

DO NOT USE COPPER CLAD ALUMINIUM (CCA) Cat 5/6/7 CABLE FOR HDBASET PRODUCTS. 

Whichever network cable type you choose, ensure that the main wiring architecture is ‘solid core’, not stranded ‘patch’ cabling. Patch cabling can be used for the last few metres of a run (say from a wallplate) but should be avoided over the longer runs as signal transfer over stranded cores is heavily reduced.

The use of pre-made leads is not recommended unless you can be absolutely sure of their construction credentials (i.e. solid core 568B)

  • Shielded cables

Unlike other systems, shielded FTP cable is not a stipulation. If however you preferred this type of cable please ensure compatible shielded accessories are used. Failure to terminate cable screen at all points can induce interference rather than eliminating it.

  • Best Practice

Best practice advice is to always use a straight piece of cable terminated directly at the matrix and the receiver ends.

  • HDBaseT with patch panels & wall plates

If the patch panels are terminated correctly and well, there is minimal loss of distance with HDBaseT.

The use of wallplates and patch panels always has the potential to cause increased resistance on the cable, introducing ‘pinch points’ for signal transmission and could reduce advertised transmission lengths.

TIP – instead of using RJ45 wallplates, use brush plates instead to maintain the neat finish. A search for “brush plates” will yield many results.

  • Can I use HDBaseT Extenders over PowerLine?

HDBaseT is not a signal type that can travel over powerline/homeplug network extension systems.

  • Connection termination

Terminate the cabling using RJ45 connectors to the 568B wiring standard (shown below).

RJ45 568A and 568B wiring diagram-932-20

  • General Troubleshooting Advice

Check that the Cat cable is not bent, knotted, kinked or distorted in any way that would prevent these high frequency signals from traveling throughout the intended length.  

Also, ensure that the cables as far away from potential sources of EMI (Electro-Magnetic Interference) such as electrical cables, transformers, light fixtures, etc.) as possible. Cables should maintain a 300mm separation from power cables.

Try re-terminating the RJ45 connectors again, making absolutely sure that every termination is perfect. Ensure that the RJ45 connectors are fully inserted and click locked into place firmly and securely to ensure perfect connector connection

  • Suggested Installation Do’s and Don’ts

DO maintain the twists of the pairs as close as possible to the point of termination, or no more than 13mm untwisted.

DO make only gradual bends in the cable where necessary to maintain the minimum bend radius of 4 times the cable diameter or approximately 30mm radius.

DO use low-to-moderate force when pulling cable. The standard calls for a maximum of 34 N-m (newton-metres of force).

DO use cable pulling lubricant for cable runs that may otherwise require great force to install. (You will be amazed at what a difference the cable lubricant will make)

DO keep Category cables as far away from potential sources of EMI (Electro-Magnetic Interference) such as electrical cables, transformers, light fixtures, etc.) as possible. Cables should maintain a 300mm separation from power cables.

DON’T allow the cable to be sharply bent, twisted, or kinked at any time. This can cause permanent damage to the geometry of the cable and cause transmission failures.

DON’T over-tighten cable ties or use plastic ties.

DON’T EVER splice or bridge Category cable at any point.

DON’T use excessive force when pulling cable.

DON’T use oil or any other lubricant not specifically designed for Category network cable pulling as they can infiltrate the cable jacket, causing damage to the insulation.

DON’T tie cables to electrical conduits, or lay cables on electrical fixtures

DON’T install cables taut. A good installation should have the cables loose, but never sagging.

DON’T use staples on Category cable that crimp the cable tightly. The common T-18 and T-25 cable staples are not recommended for Category cable. However, the T-59 insulated staple gun is ideal for fastening both Category and fibre optic cabling, as it does not put any excess pressure on the cable.

DON’T use patch cords (cables) or punch down blocks.

MHUB SRX
Scaling Receiver

pdf-icon-843-498
MHUB + XTND 
Integration Kit

pdf-icon-843-498
MHUB IR
Integration Dongle

pdf-icon-843-498

Specifications

Form factor Compact unit. Mountable with optional mounting wings
Inputs x outputs 4 HDMI x 1 RJ45 HDBaseT + 1 HDMI + 1 mirrored HDMI
Video bandwidth HDMI backplane 594MHz clock / 18Gbps data
HDBT 340MHz clock / 10.2Gbps data
ESD protection ± 8kV (air-gap discharge) ± 4kV (contact discharge)
Hub control Web GUI, IR, TCP/IP, RS232, App, Alexa
App control Full control over sources, matrix hub & display functions.
Device weight Chassis: 1250g
Receiver: 125g 
Package weight 2000g
Dimensions (W/D/H) Hub 220 / 200 / 45mm (without feet)
RX 140 / 65 / 17mm
Operating temperature 32°F to 104°F (0°C to 40°C)
Storage temperature -4°F to 140°F (-20°C to 60°C)
Relative humidity 20~90 % RH (non-condensing)
Power consumption 30W (max) 0.5W (standby)
Guarantee 2/3-year guarantee (Cloud registration required)

Questions?

In order to assist us in reducing spam, please type the characters you see:

You may also like